Leaving the South Holland Oasis at 9 o'clock. I'll let those that were going to meet me in Kenosha know so we can plan our travel time to get there beforehand. What radio channel will we be using?
Announcement
Collapse
No announcement yet.
2011 Oshawa Meet and Greet
Collapse
X
-
We stop at the duty free store after leaving Grand Rapids. Before the duty free store, we top off the tanks....once you go in the DFS, you have to go across the border....
We arrived about 8PM last year.... NO stops...not even in Lansing. (Lansing area folks need to watch for us rolling through - no stops planned.....
When we all caravaned through the border crossing, we waiting a bit at the first exit, and exit after that, a furniture store....to allow those getting searched a chance to catch up.
Then its pedal down through Toronto to Oshawasigpic
Comment
-
Originally posted by Blackhawk View Post
I don't like this meet point at 1:30. I was hoping to leave super early myself, to beat rush hour traffic here and to hopefully avoid rush hour traffic in Toronto.
Steve, we should check out if the hotel has a hose and water supply, so we can wash our LLT's. I don't know if anyone has set up wash stations, but I like to detail my car myself.
The quality inn (BBOMG hotel) does not have a hose...but there was a car wash close by....sigpic
Comment
-
Originally posted by Toasty View PostSteve, are you going to be our travel coordinator, or to we need to appoint a travel coordinator?2018 ZL1 A10 Convertible, Kooks Longtube Headers (to be installed 8Jan) Full Kooks exhaust from Kooks R&D in Mooresville, NC, ZL1 painted GFX, My ShowStopper Custom Engine Cover Kit and painted CAI. For Sale! Color Shift Lights coming soon[/SIZE][/B]
Comment
-
Yep I am going to Blame whoever canx next LOL....If they didn't come it's their fault! LOL2018 ZL1 A10 Convertible, Kooks Longtube Headers (to be installed 8Jan) Full Kooks exhaust from Kooks R&D in Mooresville, NC, ZL1 painted GFX, My ShowStopper Custom Engine Cover Kit and painted CAI. For Sale! Color Shift Lights coming soon[/SIZE][/B]
Comment
-
Yikes! did it happen durring a track run? how did it feel when it happened?
Originally posted by huggerorange73 View PostThe infamous low vin # input shaft snapped :
This bulletin just came out on Jan 11, 2011. It just states to call GM tech assistance center. I'll keep you guys posted.
#PIP4666E: Vehicle Not Moving In Any Gear - (Jan 11, 2011)
Subject:Vehicle Will Not Move In Any Gear
Models:2010 Chevrolet Camaro
Equipped With The Tremec 6-Speed Manual Transmission RPO M10
This PI was superseded to update the keywords. Please discard PIP4666D.
The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern:
Customer may comment that the vehicle will not move in any gear. Technicians may find the transmission output shaft broken.
Recommendation/Instructions:
If a vehicle comes into the dealer with the concern described above please contact the General Motors Technical Assistance Center at xxx-xxx-xxxx (USA) or xxx-xxx-xxxx (Canada), TAC will supply further instructions at that time.
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.
WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION
Comment
-
Mike hows the car? Any word on parts? Time for a one piece drive shaft.....2018 ZL1 A10 Convertible, Kooks Longtube Headers (to be installed 8Jan) Full Kooks exhaust from Kooks R&D in Mooresville, NC, ZL1 painted GFX, My ShowStopper Custom Engine Cover Kit and painted CAI. For Sale! Color Shift Lights coming soon[/SIZE][/B]
Comment
-
Originally posted by Orange5thGen View PostMike hows the car? Any word on parts? Time for a one piece drive shaft.....
Best case I'll have the car back by Friday, worst case early next week....so either way I should be good for the trip!
Comment
-
Originally posted by Orange5thGen View PostYep I am going to Blame whoever canx next LOL....If they didn't come it's their fault! LOL2018 ZL1 A10 Convertible, Kooks Longtube Headers (to be installed 8Jan) Full Kooks exhaust from Kooks R&D in Mooresville, NC, ZL1 painted GFX, My ShowStopper Custom Engine Cover Kit and painted CAI. For Sale! Color Shift Lights coming soon[/SIZE][/B]
Comment
Comment