Cam PKG, R2C CAI, cutouts #'s

[Larry@Speed Inc.]

We just finished another 2010 SS LS3/M6 today.

We are planning a blower, so we did one of our blower grinds for now. The customer had installed SW 1 7/8 headers with offroad mids to stock mid-pipe a few weeks back. We then added the dual low pro DMH cutouts and planned to tune the car, but while in we decided to reschedule for a cam pkg and tune

so here we are...

SI 226/238 .570/.585 113.5 / SC CAM
PRC 670 springs
Comp pushrods
TR55's
SW 1 7/8, offroads, stock mid-pipe with DMH cutouts
stock axle back
R2C CAI
stock crank pulley
SI Dyno Tune

We had a stock dyno on this car and then the graph shows through stock axle back and open cutouts. The 452 rwhp is open cutouts which shows that the stock axle back flows pretty well as I have mentioned before.

[CAMARO SS]

What are the R2C #'s?

[Larry@Speed Inc.]

never tested it alone

[cab2g]

I REALLY want a cam, but I use the car as a daily driver, so I don't know if it'll be a good choice until I have another car for regular driving! I love the old-school idle gurgle, but I hear that overlap makes low RPM driving tricky, and bad on mileage! If only I could get that sound, great drive-ability and the same mileage!

[Larry@Speed Inc.]

This setup here drives great and should see little to no difference in fuel economy..unless it's due to your right foot.

We have many customer who do cam and head setups for DD's.

[EvoWake]

Just happened to stumble across this post; the car here is my 2010 SS, just wanted to chime in that the car drives perfectly, and runs strong, and puts out a nice power band, particularly for a blower cam. I anticipated lackluster numbers with this cam running NA, but I couldn't have been more wrong. Drives and sounds fantastic!

Speed, Inc is top notch, and Larry is a phenomenal guy to work with. This is not my first go'round with these guys, they helped get my old cam only '01 Z running 11.90s; they've always been outstanding. I would without hesitation highly recommend Larry @ Speed Inc. to anyone.

Thanks Larry, I'm looking forward to the Maggie!

[Larry@Speed Inc.]

This thread needs a little update with the TVS2300 added and tune finished today.

612 rwhp / 579 rwtq

[papabearcamaro]

Great numbers!! I am hoping to get near that in a few weeks when my car goes in.
Congrats on the great power!

[Mystic97]

yes..very good #'s and this was through the stock axle back and no cutouts. I know Andy will be getting another couple pulls soon to show the cutout gains.

John I'm sure your car will make these #'s if not a little more

[EvoWake]

Thanks guys, and thanks Larry! I'll be writing up a detailed feedback about the car and speed Inc later today after I've had some time in the sun hopin the cutouts add me a few ponies but even if not, I am more than pleased already!

[Mystic97]

Thanks guys, and thanks Larry! I'll be writing up a detailed feedback about the car and speed Inc later today after I've had some time in the sun hopin the cutouts add me a few ponies but even if not, I am more than pleased already!

cool..glad today gave you a chance to enjoy the new setup

[EvoWake]

cool..glad today gave you a chance to enjoy the new setup

It certainly did, and all I can say wow.....

This setup pulls everywhere! I thought the car was quick before but jesus.. now it's ridiculous. Chances are, even when I think its grabbing, it's likely spinning, so I won't truly get to enjoy it until Mickey Thompson gets their act together and makes the 20" radials available.
I've not yet put the cog pulleys on but you can definitely hear the TVS, although it's quiet in comparison to my exhaust.

I have to take a minute here and give huge Kudos to Speed Inc. I've used them exclusively for some time now and they have never been anything short of first class. I'd be happy to take anyone for a spin who is considering a similar setup... Trust me, you will want it. Larry has always been great to work with as have the rest of the guys @ Speed Inc. Hit these guys up, they do phenomenal work. Bryan@speedinc.com tom@speedinc.com


Will post up more as I've had more time to have fun!

Dyno chart below... first run is Stock, followed by blower cam NA, and finally Blower + Cam



Thanks for everything Larry & Speed Inc!

[cab2g]

wow!

[EvoWake]

Installed the Cog Drive Pulleys
[ame]http://www.youtube.com/watch?v=WBpADuzCqBA&feature=youtube_gdata_player[/ame]

[papabearcamaro]

Love the "oh my god" statement. lol
Sounds great!! Got the 1:1 going on mine also as I love the whine.
Thanks for posting up the video.